Upgrade XR for ASR9k/CRS/GSR by TURBOBOOT

[对于XR的升级,就我现在所知的有以下几种,如果还有其他的方法,到时再更新]
1. Golden Disk升级
类似于Ghost系统,在现有XR设备(version A)上直接把整个系统文件backup到disk卡中,然后把这个disk卡放到要升级的机箱上(version B),指定boot位置并重启,就可以直接用新系统了(version A)。省了安装系统的时间。但由于需要指定boot路径,另外还需要copy MBI文件到bootflash,所以操作起来感觉不是非常方便。

2013-9-18 更新:
在2010-9-24 更新中的第3和第4小点中,已经总结了一些GoldenDisk的内容。这里再提一下,如果从老版本升级到新版本,如3.6.3到4.0.4,又需要用FAT32,那么一定要把MBI拷贝到bootflash,否则无法识别FAT32;另外还要记住升级前要升级rommona/b的版本,原因下面有解释。

在3.6.3上升级rommon的步骤如下:
1. 从官网下载较新的rommon tar文件
2. 拷贝到disk0中
3. 执行upgrade rommon a/b all disk0

如果客户安装了很多SMU,又不知道正确的MBI路径,那么可以在老系统中把默认的MBI路径拷贝到bootflash中,然后启动,设备会自动boot这个MBI,如果MBI不正确,它会自动把正确的MBI文件copy到bootflash中,然后重启并用新MBI启动,如下所示:

Install (Node Preparation): Booting with committed software
Install (Node Preparation): Checking free space on /bootflash/
Install (Node Preparation): Copying MBI from /disk0/hfr-os-mbi-4.0.4.CSCuc17728-1.0.0/mbihfr-rp.vm
Install (Node Preparation): Copying MBI to /bootflash/disk0/hfr-os-mbi-4.0.4.CSCuc17728-1.0.0/mbihfr-rp.vm
insthelper: This node was booted with an incorrect MBI (/bootflash/disk0/hfr-os-mbi-4.0.4/mbihfr-rp.vm), rebooting self with correct boot image (/bootflash/disk0/hfr-os-mbi-4.0.4.CSCuc17728-1.0.0/mbihfr-rp.vm).

2. Turboboot 升级
完全重新安装,在Rommon模式中download mini PIE文件,感觉像之前IOS环境下的启动新版本那样。只不过XR是要安装,而IOS直接调用。
3. 直接在原有系统上升级
打个比方说,在windows xp的基础上直接升级到windows 7,这样即使windows 7装完了,在新系统中仍然有老系统的东西。所以一般不推荐用这种方法。对于disk存储介质,最好只有1种操作系统,这样稳定些。

2013-11-29 更新:
在现有系统升级又分两种方式:
一种是直接安装PIE文件,如果你的版本是A,要升级B,那么直接active B的PIE即可,但要注意,A和B的PIE要保持一致才能安装,否则会有兼容,如下所示(注:现有系统升级后,配置是保留的):

RP/0/RP0/CPU0:LAB-CRS-1(admin)#show ins ac sum
Wed Nov 20 08:56:25.113 UTC
Default Profile:
  Admin Resources
  SDRs:
    Owner
  Active Packages:
    disk0:hfr-mpls-px-4.0.4
    disk0:hfr-mgbl-px-4.0.4
    disk0:hfr-mini-px-4.0.4

RP/0/RP0/CPU0:LAB-CRS-1(admin)#install activate disk0:hfr-mini-px-4.2.4 sync
Wed Nov 20 08:56:33.503 UTC
Install operation 34 '(admin) install activate disk0:hfr-mini-px-4.2.4 synchronous' started by user 'cisco' via CLI at 08:56:33 UTC Wed Nov 20 2013.
Error:    Cannot proceed with the activation because of the following package incompatibilities:
Error:      hfr-mgbl-supp-4.0.4 needs iosxr-fwding-4.0.4, or equivalent, to be active on the same nodes.
Error:      hfr-mgbl-supp-4.0.4 needs hfr-fwding-4.0.4, or equivalent, to be active on the same nodes.
Error:      hfr-mgbl-supp-4.0.4 needs hfr-base-4.0.4, or equivalent, to be active on the same nodes.
Error:      hfr-mgbl-supp-4.0.4 needs iosxr-infra-4.0.4, or equivalent, to be active on the same nodes.
Error:      hfr-mgbl-supp-4.0.4 needs hfr-os-support-4.0.4, or equivalent, to be active on the same nodes.
Error:      hfr-mgbl-supp-4.0.4 needs iosxr-os-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mgbl-4.0.4 needs iosxr-routing-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mgbl-4.0.4 needs iosxr-fwding-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mgbl-4.0.4 needs iosxr-infra-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mgbl-4.0.4 needs iosxr-os-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mpls-4.0.4 needs iosxr-routing-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mpls-4.0.4 needs iosxr-fwding-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mpls-4.0.4 needs iosxr-infra-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mpls-4.0.4 needs iosxr-os-4.0.4, or equivalent, to be active on the same nodes.
Error:    Suggested steps to resolve this:
Error:     - check the installation instructions.
Error:     - activate or deactivate the specified packages on the specified nodes.
Install operation 34 failed at 08:56:40 UTC Wed Nov 20 2013.
RP/0/RP0/CPU0:LAB-CRS-1(admin)#
RP/0/RP0/CPU0:LAB-CRS-1(admin)#install add tftp://10.75.41.57/hfr-mgbl-px.pie-4.2.4 sync
Wed Nov 20 08:57:39.796 UTC
Install operation 35 '(admin) install add /tftp://10.75.41.57/hfr-mgbl-px.pie-4.2.4 synchronous' started by user 'cisco' via CLI at 08:57:39 UTC Wed Nov 20 2013.
Info:     The following package is now available to be activated:
Info:
Info:         disk0:hfr-mgbl-px-4.2.4
Info:
Info:     The package can be activated across the entire router.
Info:
Install operation 35 completed successfully at 08:58:02 UTC Wed Nov 20 2013.
RP/0/RP0/CPU0:LAB-CRS-1(admin)#install activate disk0:hfr-mini-px-4.2.4 disk0:hfr-mgbl-px-4.2.4 sync
Wed Nov 20 08:58:46.818 UTC
Install operation 36 '(admin) install activate disk0:hfr-mini-px-4.2.4 disk0:hfr-mgbl-px-4.2.4 synchronous' started by user 'cisco' via CLI at 08:58:46 UTC Wed Nov 20
2013.
Error:    Cannot proceed with the activation because of the following package incompatibilities:
Error:      iosxr-mpls-4.0.4 needs iosxr-routing-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mpls-4.0.4 needs iosxr-fwding-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mpls-4.0.4 needs iosxr-infra-4.0.4, or equivalent, to be active on the same nodes.
Error:      iosxr-mpls-4.0.4 needs iosxr-os-4.0.4, or equivalent, to be active on the same nodes.
Error:    Suggested steps to resolve this:
Error:     - check the installation instructions.
Error:     - activate or deactivate the specified packages on the specified nodes.
Install operation 36 failed at 08:58:54 UTC Wed Nov 20 2013.
RP/0/RP0/CPU0:LAB-CRS-1(admin)#
RP/0/RP0/CPU0:LAB-CRS-1(admin)#install deactivate disk0:hfr-mpls-px-4.0.4
Wed Nov 20 08:59:20.777 UTC
Install operation 37 '(admin) install deactivate disk0:hfr-mpls-px-4.0.4' started by user 'cisco' via CLI at 08:59:20 UTC Wed Nov 20 2013.
Info:     Install Method: Parallel Process Restart
The install operation will continue asynchronously.
RP/0/RP0/CPU0:LAB-CRS-1(admin)#show ins ac sum
Wed Nov 20 09:00:36.442 UTC
Default Profile:
  Admin Resources
  SDRs:
    Owner
  Active Packages:
    disk0:hfr-mgbl-px-4.0.4
    disk0:hfr-mini-px-4.0.4

RP/0/RP0/CPU0:LAB-CRS-1(admin)#
RP/0/RP0/CPU0:LAB-CRS-1(admin)#install activate disk0:hfr-mini-px-4.2.4 disk0:hfr-mgbl-px-4.2.4 sync
Wed Nov 20 09:00:50.380 UTC
Install operation 38 '(admin) install activate disk0:hfr-mini-px-4.2.4 disk0:hfr-mgbl-px-4.2.4 synchronous' started by user 'cisco' via CLI at 09:00:50 UTC Wed Nov 20
2013.
Info:     This operation will reload the following nodes in parallel:
Info:         0/7/CPU0 (LC) (SDR: Owner)
Info:         0/15/SP (MSC-DRP-SP) (Admin Resource)
Info:         0/15/CPU0 (LC) (SDR: Owner)
Info:         0/RP0/CPU0 (CRS16-RP-x86) (SDR: Owner)
Info:         0/FC0/SP (SP) (Admin Resource)
Info:         0/FC1/SP (SP) (Admin Resource)
Info:         0/AM0/SP (SP) (Admin Resource)
Info:         0/AM1/SP (SP) (Admin Resource)
Info:         0/SM2/SP (140G-Fabric-SP-B) (Admin Resource)
Info:         0/SM3/SP (140G-Fabric-SP-B) (Admin Resource)
Info:         0/SM4/SP (140G-Fabric-SP-B) (Admin Resource)
Info:         0/SM5/SP (140G-Fabric-SP-B) (Admin Resource)
Info:         0/SM6/SP (140G-Fabric-SP-B) (Admin Resource)
Info:         0/SM7/SP (140G-Fabric-SP-B) (Admin Resource)
Proceed with this install operation (y/n)? [y]
Info:     Install Method: Parallel Reload
Info:     The changes made to software configurations will not be persistent across system reloads. Use the command '(admin) install commit' to make changes persistent.
Info:     Please verify that the system is consistent following the software change using the following commands:
Info:         show system verify
Info:         install verify packages
Install operation 38 completed successfully at 09:06:24 UTC Wed Nov 20 2013.
RP/0/RP0/CPU0:LAB-CRS-1(admin)#

另一种方式是直接安装下载后的TAR文件,或者自己做的一个TAR文件,以后有机会抓着部分信息,在更新上去。

关于rommon的一些问题
CRS一共有两个rommon,rommon A和rommon B。平时启动都是rommon B,rommon A只做一些工厂检测用。[如果rommon A的版本不低于1.52(这是CRS的需求,9k的另需要确认),就不用升级rommon A。因为每次启动都会由rommon A 去disk卡中check一些信息,感觉像是rommon在加载一些命令集(monlib ?),使得如果rommonB不能启动,或是坏了,可以直接从rommon A启动进行检测。如果版本低于1.52,rommon A就会不识别fat32的disk,所以就停在那里无法继续进行加载rommon B,如果是fat16,就没有任何问题]

2012-7-23 更新:
2010-9-24 更新

对于为什么要升级rommon A,前几天又重新看了下文档,发现大概理解了其中的原因:
就目前来说,CRS的rommon没有直接支持FAT32的指令集,所以当启动系统时,需要FAT16的格式。为了让CRS支持FAT32启动,研发人员想出来一个折中的办法,这就是Split Boot,简单说来就是在1.52以后的rommon版本里加了一些特殊的monlib指令(把启动路径自动改为BOOT=bootflash:disk0/mbi.vm),这些指令让系统去bootflash启动MBI,因为bootflash是FAT16的。当MBI启动后,它会去调用disk(FAT32)中其他的启动文件,从而支持FAT32。当然只有rommon里的新指令集是不够的,还要有触发条件—新软件,两者必须匹配,软件3.8.4以后才支持Split Boot因此当你用FAT32升级3.8.4或更高版本时,如果rommon A的版本还是在1.52之前,那么它不识别FAT32的文件,也不会去bootflash里加载相应的MBI,这样就会不断重启。那么是否在老rommon(1.49)下3.8.4可以用fat16格式的disk直接boot呢?
1. 3.8.4,4.0.4均做过测试,在fat16,能正常读取disk0的信息,另外也会自动把disk0里的mbi拷贝到bootflash中(rommon版本1.49):

boot: booting from disk0:hfr-os-mbi-4.0.4/mbihfr-rp.vm

Sep 24 16:54:10.583 : Install (Node Preparation): Booting with committed software
Sep 24 16:54:45.555 : Install (Node Preparation): Checking free space on /bootflash/
Sep 24 16:54:45.559 : Install (Node Preparation): Copying MBI from /disk0/hfr-os-mbi-4.0.4/mbihfr-rp.vm
Sep 24 16:54:45.561 : Install (Node Preparation): Copying MBI to /bootflash/disk0/hfr-os-mbi-4.0.4/mbihfr-rp.vm

2. 对于fat32,因为根本就不识别fat32,所以一直flapping,如下信息(rommon版本1.49):

Fail to open file name mbi_image
Acquiring backplane mastership.succeeded.
Chassis type: 480

CARD_RACK_NUMBER: 0
CARD_SLOT_NUMBER: 0
CPU_INSTANCE: 1
RACK_SERIAL_NUMBER: TBM15279115
MBI Validation starts …Our MAC address is 0025.8432.4320
Interface link changed state to UP.
Interface link state up.

MBI validation sending request.
HIT CTRL-C to abort

No MBI confirmation received from dSC

boot: booting from disk0:hfr-os-mbi-4.0.4/mbihfr-rp.vm
loadprog: error – on file open
boot: cannot load “disk0:hfr-os-mbi-4.0.4/mbihfr-rp.vm“ú

Initializing DDR SDRAM…found 4096 MB
3. 那么用fat16的disk0启动,格式化disk1为fat32,并用“admin system backup disk1:”做一个Godendisk,另外确保flash里有mbi。重启进入rommon,改启动路径,指向disk1,reset,失败(rommon版本1.49)。。。

RP/0/RP0/CPU0:ios(admin)#system backup disk1:
Tue Sep 25 10:01:20.304 UTC
Info: node0_RP0_CPU0: formatting target device
Info: node0_RP0_CPU0: copying admin configuration
Info: node0_RP0_CPU0: copying SDR configuration
Info: node0_RP0_CPU0: copying installed software
Info: node0_RP0_CPU0: backup complete.
Info: node0_RP0_CPU0: verifying admin configuration
Info: node0_RP0_CPU0: verifying SDR configuration
Info: node0_RP0_CPU0: verifying installed software
Info: node0_RP0_CPU0: verify complete.
Info: node0_RP0_CPU0: command succeeded.
RP/0/RP0/CPU0:ios(admin)#
RP/0/RP0/CPU0:ios(admin)#exit
RP/0/RP0/CPU0:ios#show media
Tue Sep 25 10:20:37.669 UTC

Media Information for 0/RP0/CPU0.
                   Image   Current  Part
  Mountpoint       FsType  FsType   Size   State         DrvrPid  Mirror  Flags
================================================================================
  /disk0:          FAT16   FAT16    2.0G Mounted         0040982  Enabled
  /disk0a:         FAT16   FAT16    2.0G Mounted         0040982
  /disk1:          FAT16   FAT32    2.0G Mounted         0720934          Formatted Restar
  /disk1a:         FAT16   FAT32    2.0G Mounted         0720934          Formatted Restar

P/0/RP0/CPU0:ios#dir bootflash:/disk0
Tue Sep 25 10:21:10.149 UTC
Directory of bootflash:/disk0
2031620 drwx 44 Mon Sep 24 19:23:21 2012 hfr-os-mbi-4.0.4
62390272 bytes total (16181456 bytes free)

rommon B2 > unset BOOT
rommon B3 > BOOT=disk1:hfr-os-mbi-4.0.4/mbihfr-rp.vm
rommon B4 > sync
rommon B5 > reset

boot: booting from disk1:hfr-os-mbi-4.0.4/mbihfr-rp.vm
loadprog: error – on file open
boot: cannot load “disk1:hfr-os-mbi-4.0.4/mbihfr-rp.vm“ú
4. 这是为什么?这里有两个原因,首先mbi只存在bootlfash中disk0这个目录下,但系统文件装载在disk1中,所以必须在bootflash中建立一个disk1的目录,并把mbi考到里面;其次因为rommon没有升级,还是1.49,所以也不会去bootflash中找mbi,下面的启动信息是在rommon升级后,mbi也已考到bootflash中disk1文件夹下:

validate_mbi: could not find “;” in path
disk1:hfr-os-mbi-4.0.4/mbihfr-rp.vmAcquiring backplane mastership.succeeded.
Chassis type: 480

CARD_RACK_NUMBER: 0
CARD_SLOT_NUMBER: 0
CPU_INSTANCE: 1
RACK_SERIAL_NUMBER: TBM15279115

MBI Validation starts …Our MAC address is 0025.8432.4320
Interface link changed state to UP.
Interface link state up.

MBI validation sending request.
HIT CTRL-C to abort

No MBI confirmation received from dSC
boot: booting from bootflash:disk1/hfr-os-mbi-4.0.4/mbihfr-rp.vm

2012-9-4 更新:
加入GSR升级XR的步骤:
1. 下载支持XR的boot image,如“c12kprp-boot-mz.120-32.SY15.bin”并用此软件启动
2. 启动后更改启动参数“config-register 0x0”,进入rommon
3. 设置相关的启动参数,如:
rommon 1 > unset BOOT
rommon 2 > BOOTLDR=bootflash:c12kprp-boot-mz.120-32.SY15.bin
rommon 3 > TURBOBOOT=on,disk0
rommon 4 > sync
rommon 5 > reset
4. reset后加载XR image,“boot tftp c12k-mini.vm-4.1.2 64.1.1.1”
注意其中需要设置IP、网关地址,TFTP等参数,以及PRP型号和内存大小都有要求。如果内存不够,再加入补丁或安装pie文件时,可能会导致协议flapping,如BGP,因为协议也占用内存的资源,在xr下可以用“show watchdog threshold memory defaults location all” 去查看内存门限及使用情况
更详细的请看下面的官方文档:
Upgrading a Single RP Cisco 12000 Series Router from Cisco IOS Software to Cisco IOS XR Software – 升级过程
Cisco XR 12000 Series Router for Cisco IOS XR Software Release 4.2.3 – 升级XR时,型号,内存的要求

注意:如果上面方法不行,那么老老实实的用boot image启动,在boot image里设置register 0x0,然后重启进入rommon,在进行更改。

更详细的升级相关文档,可以参考下面link,包括CRS/ASR9k升级的所有必备文档:
Cisco IOS XR General Information
ASR9000/XR Understanding Turboboot and initial System bring up

升级过程及注意事项

一般用Turboboot就可以了,最近刚刚升了ASR9k的版本,下面是记录整理:
1. 去网站上下载相应的tar文件,下来后解压出来,里面有很多pie文件,升级用mini pie
2. 升级前请确定rommon版本,如需要,先升级rommon版本,在此不作介绍
3. 改变confreg 到0x0, reload localtion all进入rommon
4. 设置网关及自己的地址,注意download ios是通过management口,如下信息:
IP_ADDRESS=10.1.1.1
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.1.1.254
TFTP_SERVER=64.1.1.1
5. 如果线路质量不是特别好,建议把“TFTP_RETRY_COUNT=3”改成10,否则retry 3次不成功后会失败。
6. 开启Turboboot“TURBOBOOT=on,disk0,format”,其中format是安装前格式整个disk0,所以注意要把需要备份的内容考到其他地方

2013-10-24 更新:
在ASR9001上,这么写Turboboot脚本可能会失效,而且不报任何错误,就是进不了Turboboot,所以可以尝试在disk0后面加“:”,完整的写法是:
TURBOBOOT=on,disk0:,format
sync

7. 设置完后,用“sync”命令同步,并用“set”去查看是否写上
8. 启动新版本“boot tftp://64.1.1.1/asr9k-mini-p.vm-4.2.0”,内存加载
9. 启动后会执行Turboboot,format disk0并安装文件,此时系统文件是在memory中,安装好后会自动用新文件(disk中)重启
10.启动后安装相应的pie文件,完成,注意当你安装多个pie文件时,需要在路径与文件名中间留空格,如果仅装一个,那么不需要,对于combo的SMU可以直接安装tar文件
(admin)#install add source tftp://64.1.1.1/ asr9k-services-p.pie-4.2.0 asr9k-k9sec-p.pie-4.2.0 asr9k-mpls-p.pie-4.2.0 sync
(admin)#install activate disk0:asr9k-services-p-4.2.0 disk0:asr9k-k9sec-p-4.2.0 disk0:asr9k-mpls-p-4.2.0 sync

如果安装包多,建议安装时直接acti,否则可能会有问题,因为SMU之前是需要关联的:
install add source tftp://64.1.1.1/ xxx activate sync

11.确认安装,如不输入,重启后虽然disk中有PIE文件,但将无法启动,相当于索引文件没有保存
(admin)#install commit

下面是整过升级过程信息,供参考:

rommon B4 > TFTP_RETRY_COUNT=10
rommon B5 > sync
rommon B6 > boot tftp://64.1.1.1/asr9k-mini-p.vm-4.2.0

          IP_ADDRESS: 10.1.1.1
      IP_SUBNET_MASK: 255.255.255.0
     DEFAULT_GATEWAY: 10.1.1.254
         TFTP_SERVER: 64.1.1.1
           TFTP_FILE: asr9k-mini-p.vm-4.2.0

Performing tftpdnld

Mgt LAN 0 interface is selected
tsec_init_hw: configuring FE (port 1) for: Auto Speed, Auto Duplex

tsec_init_interface: hardware initialization completed

Receiving asr9k-mini-p.vm-4.2.0 from 64.1.1.1 !!!!!!!!!!!!!!!!!!
tftp_process_packet: last packet, block=58356, size=310.
File reception completed.
Image size=298313526, TFTP download size=298313526
.....................................................................
program load complete, entry point: 0x201d9c, size: 0x11c7d836
Attempting to start second CPU
Config = SMP, Running = SMP
Board type: 0x00100304
Card Capability = 0xffffffff
BSP: Board type : RO-RSP2
tracelogger: starting tracing in background ring mode
tracelogger running with args: -startring -F 1 -F 2
czip:326:mount=/dev/shmem, image=0, remove=0x1
czip: strings=ffff23f0, as=ffff29f8, num=0x480
czip: 356:start_addr=60185000, in_size=0x109e55b2

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco IOS XR Software for the Cisco XR ASR9K, Version 4.2.0
Copyright (c) 2011 by Cisco Systems, Inc.
May 18 06:43:09.167 : Install (Node Preparation): Initializing VS Distributor...
May 18 06:43:19.272 : Install (Node Preparation): Booting with committed software
FPD ltrace_file_name => fpd-agent/fiarsp
May 18 06:43:38.629 : TURBOBOOT: Turboboot process started
!---Turboboot 开始
May 18 06:43:38.713 : TURBOBOOT: Checking size of device disk0:
May 18 06:43:38.752 : TURBOBOOT:    OK
May 18 06:43:38.776 : TURBOBOORP/0/RSP0/CPU0:May 18 06:43:38.792: syslogd_helper: [95]: dsc_event_handler: GotT SysMgr dSC event : 1
: Checking size of MBI device bootflash:
May 18 06:43:38.824 : TURBOBOOT:    OK
May 18 06:43:38.846 : TURBOBOOT: Waiting for Admin Config to complete
FPD ltrace_file_name => fpd-agent/longbeach
FPD ltrace_file_name => fpd-agent/tempo
May 18 06:43:59.144 : TURBOBOOT: Admin Config completed
May 18 06:43:59.222 : TURBOBOOT: Formatting disk0:
!---Formatting 开始

ios con0/RSP0/CPU0 is now available

Press RETURN to get started.

May 18 06:44:05.617 : TURBOBOOT: Formatting disk0: complete
May 18 06:44:05.632 : TURBOBOOT: Checking Configuration File System (attempt #1).
May 18 06:44:06.688 : TURBOBOOT: Creating any missing directories in ADMIN Configuration File system...
May 18 06:44:07.895 : TURBOBOOT: OK
May 18 06:44:08.133 : TURBOBOOT: Initializing ADMIN Configuration Version Manager...
RP/0/RSP0/CPU0:May 18 06:43:30.985 : spp[92]: %PKT_INFRA-spp-3-ERR : Node 'port3/classify' disposition 4 ('ptp_off_rx_node') not found, using 'drop' instead
RP/0/RSP0/CPU0:May 18 06:43:35.880 : fiarsp[215]: DEBUG: FPD ltrace (fpd-agent/fiarsp) Initialization successful for fiarsp
RP/0/RSP0/CPU0:May 18 06:43:45.275 : longbeach[68]: DEBUG: FPD ltrace (fpd-agent/longbeach) Initialization successful for longbeach
RP/0/RSP0/CPU0:May 18 06:43:46.215 : tempo[406]: DEBUG: FPD ltrace (fpd-agent/tempo) Initialization successful for tempo
RP/0/RSP0/CPU0:May 18 06:43:46.509 : pwrmon[352]: %PLATFORM-PWRMON-2-MODULE_FAILURE : Power-module 0/PM2/SP failure condition raised
RP/0/RSP0/CPU0:May 18 06:43:47.769 : pwrmon[352]: %PLATFORM-PWRMON-2-MODULE_FAIL_REASON : Power-module 0/PM2/SP fail reason: Module shutdown due to no external stable input power feed present
RP/0/RSP0/CPU0:May 18 06:43:55.223 : cfgmgr-rp[161]: ISSU: Starting sysdb bulk start session
RP/0/RSP0/CPU0:May 18 06:43:58.125 : placed[340]: Got node role 4 :1 0 1
RP/0/RSP0/CPU0:May 18 06:43:59.692 : hsbi_fpd_agent[234]: DEBUG: FPD ltrace (fpd-agent/hsbi_fpd_agent) Initialization successful for hsbi_fpd_agent
RP/0/RSP0/CPU0:May 18 06:44:00.553 : rommon_fpd_agent[361]: DEBUG: FPD ltrace (fpd-agent/rommon_fpd_agent) Initialization successful for rommon_fpd_agent
RP/0/RSP0/CPU0:May 18 06:44:03.921 : pfm_node_rp[338]: %PLATFORM-CLKCTRL_T-3-PLL_T0_STATE_FREERUN : Set|tempo[196672]|Timing and CPI Controller(0x101c000)|The clock-control T0 PLL (reference clock for all interfaces) is in FREERUN mode.
May 18 06:44:12.176 : TURBOBOOT: OK
May 18 06:44:12.212 : TURBOBOOT: Syncing ADMIN commit database with running configuration...
May 18 06:44:12.866 : TURBOBOOT: OK
May 18 06:44:12.868 : TURBOBOOT: Configuration File System check successful.
May 18 06:44:12.871 : TURBOBOOT: Syncing AAA admin plane username configuration...
RP/0/RSP0/CPU0:May 18 06:44:12.917 : locald_DSC[298]: %SECURITY-LOCALD-3-ROOT_USERDB_INIT_FAIL : Failed to open password file during finalization: path /dev/rdsfs/aaa/__admin__/__root_admin%%, error: No such file or directory
RP/0/RSP0/CPU0:May 18 06:44:12.919 : locald_DSC[298]: %SECURITY-LOCALD-3-LWA_ADD_FAIL : Failed to add the username admin to lightweight authentication password database: No such file or directory
RP/0/RSP0/CPU0:May 18 06:44:12.919 : locald_DSC[298]: apply error 2 admin/cfg/gl/aaa/username/admin/group/root-system
May 18 06:44:12.942 : TURBOBOOT: OK
RP/0/RSP0/CPU0:May 18 06:44:12.926 : locald_DSC[298]: %SECURITY-LOCALD-3-LWA_ADD_FAIL : Failed to add the username admin to lightweight authentication password database: No such file or directory
RP/0/RSP0/CPU0:May 18 06:44:12.926 : locald_DSC[298]: apply error 2 admin/cfg/gl/aaa/username/admin/secret
RP/0/RSP0/CPU0:May 18 06:44:12.931 : locald_DSC[298]: %SECURITY-LOCALD-3-LWA_ADD_FAIL : Failed to add the username cisco to lightweight authentication password database: No such file or directory
RP/0/RSP0/CPU0:May 18 06:44:12.931 : locald_DSC[298]: apply error 2 admin/cfg/gl/aaa/username/cisco/group/root-system
RP/0/RSP0/CPU0:May 18 06:44:12.937 : locald_DSC[298]: %SECURITY-LOCALD-3-LWA_ADD_FAIL : Failed to add the username cisco to lightweight authentication password database: No such file or directory
RP/0/RSP0/CPU0:May 18 06:44:12.937 : locald_DSC[298]: apply error 2 admin/cfg/gl/aaa/username/cisco/secret
May 18 06:44:13.316 : TURBOBOOT: Removing insttr directory finished: No error
May 18 06:44:13.354 : TURBOBOOT: Cleaning MBI device 'bootflash:'
May 18 06:44:14.362 : TURBOBOOT: Cleaning MBI device bootflash: complete
May 18 06:44:17.397 : TURBOBOOT: Detected install director running after 3 seconds
RP/0/RSP0/CPU0:May 18 06:44:19.059 : uti_fpd_agent[415]: DEBUG: FPD ltrace (fpd-agent/uti_fpd_agent) Initialization successful for uti_fpd_agent
RP/0/RSP0/CPU0:May 18 06:44:19.800 : sysmgr[96]: %OS-SYSMGR-4-MANDATORY_REBOOT_OVERRIDE : mandatory reboot option overridden by request
Install operation 1 '(admin) install copy-package mem: to disk0:' started by
user '(Unknown)' via CLI at 06:44:23 UTC Fri May 18 2012.
May 18 06:44:38.922 : TURBOBOOT: Checking available free space in disk0:
May 18 06:44:48.732 : TURBOBOOT:  Done May 18 06:44:48.741 : TURBOBOOT: Copying installed files from mem: to disk0:
!---开始安装系统文件,从memory到disk0
May 18 06:44:48.794 : TURBOBOOT:  Copying package/meta-data contents:
asr9k-os-4.2.0
May 18 06:44:48.794 : TURBOBOOT:    Please wait...
May 18 06:44:48.802 : TURBOBOOT:  Copying package/meta-data contents:
asr9k-ce-4.2.0
May 18 06:44:48.802 : TURBOBOOT:    Please wait...
May 18 06:44:50.204 : TURBOBOOT:    Copying complete: asr9k-ce-4.2.0
May 18 06:44:50.228 : TURBOBOOT:  Copying package/meta-data contents:
asr9k-fpd-4.2.0
May 18 06:44:50.229 : TURBOBOOT:    Please wait...
May 18 06:46:19.076 : TURBOBOOT:    Copying complete: asr9k-fpd-4.2.0
May 18 06:46:19.135 : TURBOBOOT:  Copying package/meta-data contents:
asr9k-cpp-4.2.0
May 18 06:46:19.136 : TURBOBOOT:    Please wait...
May 18 06:46:42.633 : TURBOBOOT:    Copying complete: asr9k-cpp-4.2.0
May 18 06:46:42.647 : TURBOBOOT:  Copying package/meta-data contents:
asr9k-scfclient-4.2.0
May 18 06:46:42.648 : TURBOBOOT:    Please wait...
May 18 06:46:43.257 : TURBOBOOT:    Copying complete: asr9k-scfclient-4.2.0
May 18 06:46:43.270 : TURBOBOOT:  Copying package/meta-data contents:
asr9k-diags-supp-4.2.0
May 18 06:46:43.270 : TURBOBOOT:    Please wait...
May 18 06:46:44.253 : TURBOBOOT:    Copying complete: asr9k-diags-supp-4.2.0
May 18 06:46:44.291 : TURBOBOOT:  Copying package/meta-data contents:
asr9k-fwding-4.2.0
May 18 06:46:44.292 : TURBOBOOT:    Please wait...
May 18 06:47:42.287 : TURBOBOOT:    Copying complete: asr9k-fwding-4.2.0
May 18 06:47:42.324 : TURBOBOOT:  Copying package/meta-data contents:
asr9k-base-4.2.0
May 18 06:47:42.325 : TURBOBOOT:    Please wait...
May 18 06:48:14.907 : TURBOBOOT:    Copying complete: asr9k-base-4.2.0
May 18 06:48:14.922 : TURBOBOOT:  Copying package/meta-data contents:
asr9k-os-mbi-4.2.0
May 18 06:48:14.922 : TURBOBOOT:    Please wait...
May 18 06:48:29.464 : TURBOBOOT:    Copying complete: asr9k-os-mbi-4.2.0
May 18 06:48:29.486 : TURBOBOOT:  Copying package/meta-data contents:
iosxr-ce-4.2.0
May 18 06:48:29.486 : TURBOBOOT:    Please wait...
May 18 06:48:40.023 : TURBOBOOT:    Copying complete: iosxr-ce-4.2.0
May 18 06:48:40.037 : TURBOBOOT:  Copying package/meta-data contents:
iosxr-diags-4.2.0
May 18 06:48:40.037 : TURBOBOOT:    Please wait...
May 18 06:48:41.422 : TURBOBOOT:    Copying complete: iosxr-diags-4.2.0
May 18 06:48:41.444 : TURBOBOOT:  Copying package/meta-data contents:
iosxr-routing-4.2.0
May 18 06:48:41.444 : TURBOBOOT:    Please wait...
May 18 06:48:58.596 : TURBOBOOT:    Copying complete: iosxr-routing-4.2.0
May 18 06:48:58.674 : TURBOBOOT:  Copying package/meta-data contents:
iosxr-fwding-4.2.0
May 18 06:48:58.674 : TURBOBOOT:    Please wait...
May 18 06:51:05.567 : TURBOBOOT:    Copying complete: iosxr-fwding-4.2.0
May 18 06:51:05.680 : TURBOBOOT:  Copying package/meta-data contents:
iosxr-infra-4.2.0
May 18 06:51:05.680 : TURBOBOOT:    Please wait...
May 18 06:53:09.370 : TURBOBOOT:    Copying complete: iosxr-infra-4.2.0
May 18 06:53:10.428 : TURBOBOOT:
May 18 06:53:10.428 : TURBOBOOT: Packages have been copied to disk0:. Removing
this device could be disruptive to the system.
May 18 06:53:10.428 : TURBOBOOT:
May 18 06:53:10.429 : TURBOBOOT: Copying the MBI to bootflash:
!---Turboboot默认直接把新的MBI考到bootflash中,所以不用手动copy
RP/0/RSP0/CPU0:May 18 06:54:01.379 : lrd[302]: %HA-LRD-4-UNEXPECTED : Unexpected: mgmt_node_timeout_handler: LR plane ready signalled but band not final: 0x%x : 0x4  : pkg/bin/lrd : (PID=221256) :  -Traceback= 4d8f4ec4 4c25ead8 4c25c8e0 4c25c9e4 4c2d59f0 4c2c53c4
May 18 06:55:14.112 : TURBOBOOT: New boot image is
disk0:asr9k-os-mbi-4.2.0/0x100000/mbiasr9k-rp.vm
May 18 06:55:14.112 : TURBOBOOT: The newly copied package(s) will be activated
upon reload for the following card types:
May 18 06:55:14.113 : TURBOBOOT: RP
May 18 06:55:14.113 : TURBOBOOT: NP24-40x1GE
May 18 06:55:14.114 : TURBOBOOT: NP24-4x10GE
May 18 06:55:14.114 : TURBOBOOT: NP80-8x10GE
May 18 06:55:14.114 : TURBOBOOT: NP40-40x1GE
May 18 06:55:14.114 : TURBOBOOT: NP40-4x10GE
May 18 06:55:14.114 : TURBOBOOT: NP40-8x10GE
May 18 06:55:14.115 : TURBOBOOT: A9K-SIP-700
May 18 06:55:14.115 : TURBOBOOT: NP40-2_20_COMBO
May 18 06:55:14.115 : TURBOBOOT: NP80-16x10GE
May 18 06:55:14.115 : TURBOBOOT: A9K-SIP-500
May 18 06:55:14.115 : TURBOBOOT: NP200-24x10GE
May 18 06:55:14.116 : TURBOBOOT: NP200-2x100GE
May 18 06:55:14.116 : TURBOBOOT: NP200-5x40GE
May 18 06:55:14.116 : TURBOBOOT: NP200-8x10GE
May 18 06:55:14.116 : TURBOBOOT: NP200-MOD-SMEM
May 18 06:55:14.116 : TURBOBOOT: NP200-MOD-LMEM
May 18 06:55:14.117 : TURBOBOOT: A9K-SIP-AVSM
May 18 06:55:14.117 : TURBOBOOT: Reload then run this boot image to activate
copied packages.
May 18 06:55:14.117 : TURBOBOOT: Package copy operation is complete.
Install operation 1 completed successfully at 06:55:14 UTC Fri May 18 2012.
May 18 06:55:14.358 : TURBOBOOT: All node preparations complete:
Node 0/0/CPU0 successfully completed the preparation.
Node 0/RSP0/CPU0 successfully completed the preparation.
!---完成Turboboot
May 18 06:55:14.377 : TURBOBOOT: Resetting TURBOBOOT rommon variable to (TURBOBOOT=).
!---重置Turboboot参数
May 18 06:55:15.575 : TURBOBOOT: Setting config-register to autoboot the router and disable send break.
!---很人性化,连config-re也不用改了
May 18 06:55:15.603 : TURBOBOOT: Turboboot completed successfully: the router will now reload from disk

May 18 06:55:15.605 : TURBOBOOT: *** RESETTING IN 30 SECONDS ***
!---重启,加载新的软件版本
RP/0/RSP0/CPU0:May 18 06:55:45.671 : shelfmgr[371]: %PLATFORM-SHELFMGR-3-NODE_CPU_RESET : Node 0/0/CPU0 CPU reset detected.
[0x1902c2fb2b] Record Reboot History, reboot cause = 0x4000042, descr = Cause: Turboboot completed successfully
Process: easybake3  Traceback: 4c2461b4 4c24rebooting 

Selecting ROMMON Image... B
DDR in Interleaved mode
POST 1 : PASSED : code 0 : DDR2 Memory Quick Test

CPU Reset Reason = 0x000d
POST 2 : PASSED : code 0 : FPGA Flash Image CRC Checks

Loading Field Programmable Devices:
FPGA 0-B PROGRAMMED  : image: 0xff500028 - 0xff576cca, et: 117ms
FPGA 1-B PROGRAMMED  : image: 0xff400028 - 0xff4d1034, et: 206ms
FPGA 2-B PROGRAMMED  : image: 0xff100028 - 0xff276358, et: 369ms
FPGA 3-B PROGRAMMED  : image: 0xff000028 - 0xff0454a8, et: 69ms

System Bootstrap, Version 1.05(20101118:025914) [ASR9K ROMMON],
Copyright (c) 1994-2010 by Cisco Systems, Inc.
Compiled Wed 17-Nov-10 18:59 by saurabja

  CPUCtrl:  1.17  [00000001/00000011]
  ClkCtrl:  1.23  [00000001/00000017]
  IntCtrl:  1.15  [00000001/0000000f]
     Punt:  1.5   [00000001/00000005]
      CBC:  1.2
      BID: 0x0006

PPC 8641D (partnum 0x8004), Revision 03.00, (Core Version 02.02)
M8641 CLKIN:   66 Mhz
Core Clock: 1333 Mhz
  MPX Clock:  533 Mhz
  LBC Clock:   33 Mhz

POST 3 : PASSED : code 0 : Slot ID/Board Type Validity
PCI-E1: Ready as Root Complex
PCI-E2: Ready as Root Complex

set_chassis_type: chassis_type=0xef02ff found=TRUE
ASR9K (8641D PPC) platform with 8192 Mb of main memory

program load complete, entry point: 0x100000, size: 0x2ac20
program load complete, entry point: 0x100000, size: 0x2ac20
MBI Candidate = disk0:asr9k-os-mbi-4.2.0/0x100000/mbiasr9k-rp.vm

    CARD_SLOT_NUMBER: 0
        CPU_INSTANCE: 1
MBI Validation starts ...

Mgt LAN 0 interface is selected
tsec_init_hw: configuring FE (port 2) for: Auto Speed, Auto Duplex

tsec_init_interface: hardware initialization completed
Interface link changed state to UP.
Interface link state up.

MBI validation sending request.
HIT CTRL-C to abort
.........
No MBI confirmation received from dSC

AUTOBOOT: Boot string = disk0:asr9k-os-mbi-4.2.0/0x100000/mbiasr9k-rp.vm,1;
!---可以看到已经正常从disk0启动了
AUTOBOOT: autobootstate=0, autobootcount=0, cmd=boot disk0:asr9k-os-mbi-4.2.0/0x100000/mbiasr9k-rp.vm
program load complete, entry point: 0x100000, size: 0x2ac20

MBI size from header = 21578140,Bootflash resident MBI filesize = 21578140
...................................................................................
program load complete, entry point: 0x201d9c, size: 0x149329c
Attempting to start second CPU
Config = SMP, Running = SMP
Board type: 0x00100304
Card Capability = 0xffffffff
###################################################################################################################
BSP: Board type : RO-RSP2
tracelogger: starting tracing in background ring mode
tracelogger running with args: -startring -F 1 -F 2
              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco IOS XR Software for the Cisco XR ASR9K, Version 4.2.0
Copyright (c) 2011 by Cisco Systems, Inc.
May 18 06:57:02.001 : Install (Node Preparation): Initializing VS Distributor...
May 18 06:57:12.134 : Install (Node Preparation): Booting with committed software
FPD ltrace_file_name => fpd-agent/fiarsp
RP/0/RSP0/CPU0:May 18 06:58:06.328: syslogd_helper: [95]: dsc_event_handler: Got SysMgr dSC event : 1
FPD ltrace_file_name => fpd-agent/longbeach
FPD ltrace_file_name => fpd-agent/tempo
RP/0/RSP0/CPU0:May 18 06:57:57.906 : spp[92]: %PKT_INFRA-spp-3-ERR : Node 'port3/classify' disposition 4 ('ptp_off_rx_node') not found, using 'drop' instead
RP/0/RSP0/CPU0:May 18 06:58:04.281 : fiarsp[215]: DEBUG: FPD ltrace (fpd-agent/fiarsp) Initialization successful for fiarsp
RP/0/RSP0/CPU0:May 18 06:58:10.472 : longbeach[68]: DEBUG: FPD ltrace (fpd-agent/longbeach) Initialization successful for longbeach
RP/0/RSP0/CPU0:May 18 06:58:11.283 : pwrmon[352]: %PLATFORM-PWRMON-2-MODULE_FAILURE : Power-module 0/PM2/SP failure condition raised
RP/0/RSP0/CPU0:May 18 06:58:11.445 : tempo[406]: DEBUG: FPD ltrace (fpd-agent/tempo) Initialization successful for tempo
RP/0/RSP0/CPU0:May 18 06:58:12.346 : pwrmon[352]: %PLATFORM-PWRMON-2-MODULE_FAIL_REASON : Power-module 0/PM2/SP fail reason: Module shutdown due to no external stable input power feed present
RP/0/RSP0/CPU0:May 18 06:58:22.818 : cfgmgr-rp[161]: ISSU: Starting sysdb bulk start session
RP/0/RSP0/CPU0:May 18 06:58:37.575 : placed[340]: Got node role 4 :1 0 1
RP/0/RSP0/CPU0:May 18 06:58:41.589 : hsbi_fpd_agent[234]: DEBUG: FPD ltrace (fpd-agent/hsbi_fpd_agent) Initialization successful for hsbi_fpd_agent
RP/0/RSP0/CPU0:May 18 06:58:42.452 : rommon_fpd_agent[361]: DEBUG: FPD ltrace (fpd-agent/rommon_fpd_agent) Initialization successful for rommon_fpd_agent
RP/0/RSP0/CPU0:May 18 06:58:48.677 : pfm_node_rp[338]: %PLATFORM-CLKCTRL_T-3-PLL_T0_STATE_FREERUN : Set|tempo[217093]|Timing and CPI Controller(0x101c000)|The clock-control T0 PLL (reference clock for all interfaces) is in FREERUN mode.
RP/0/RSP0/CPU0:May 18 06:58:53.005 : cfgmgr-rp[161]: ISSU: Starting sysdb bulk start session

ios con0/RSP0/CPU0 is now available

Press RETURN to get started.

RP/0/RSP0/CPU0:May 18 06:59:06.520 : uti_fpd_agent[415]: DEBUG: FPD ltrace (fpd-agent/uti_fpd_agent) Initialization successful for uti_fpd_agent
RP/0/RSP0/CPU0:May 18 07:00:12.947 : placed[340]: LR-PLANE-READY DECLARATION
RP/0/RSP0/CPU0:May 18 07:00:14.315 : cfgmgr-rp[161]: ISSU: Starting sysdb bulk start session

User Access Verification

Username: cisco
Password: 

RP/0/RSP0/CPU0:ios#LC/0/0/CPU0:May 18 07:01:39.377 : fialc[169]: DEBUG: FPD ltrace (fpd-agent/fialc) Initialization successful for fialc
LC/0/0/CPU0:May 18 07:01:40.138 : fca_server[168]: DEBUG: FPD ltrace (fpd-agent/fca_server) Initialization successful for fca_server
LC/0/0/CPU0:May 18 07:01:49.751 : fialc[169]: %PLATFORM-UPGRADE_FPD-4-DOWN_REV : fpga1 instance 0 is down-rev (V0.42), upgrade to (V0.43). Use the "upgrade hw-module fpd" CLI in admin mode.
LC/0/0/CPU0:May 18 07:01:49.751 : fca_server[168]: %PLATFORM-UPGRADE_FPD-4-DOWN_REV : fpga2 instance 0 is down-rev (V0.09), upgrade to (V0.10). Use the "upgrade hw-module fpd" CLI in admin mode.
LC/0/0/CPU0:May 18 07:01:49.752 : fialc[169]: %PLATFORM-UPGRADE_FPD-4-DOWN_REV : fpga1 instance 1 is down-rev (V0.42), upgrade to (V0.43). Use the "upgrade hw-module fpd" CLI in admin mode.
LC/0/0/CPU0:May 18 07:02:12.023 : hsbi_fpd_agent[192]: DEBUG: FPD ltrace (fpd-agent/hsbi_fpd_agent) Initialization successful for hsbi_fpd_agent
LC/0/0/CPU0:May 18 07:02:12.665 : rommon_fpd_agent[303]: DEBUG: FPD ltrace (fpd-agent/rommon_fpd_agent) Initialization successful for rommon_fpd_agent
LC/0/0/CPU0:May 18 07:02:13.324 : rommon_fpd_agent[303]: %PLATFORM-UPGRADE_FPD-4-DOWN_REV : rommon instance 0 is down-rev (V1.03), upgrade to (V1.05). Use the "upgrade hw-module fpd" CLI in admin mode.
LC/0/0/CPU0:May 18 07:02:17.283 : fialc[169]: mace_client_init: Client already connected
LC/0/0/CPU0:May 18 07:02:17.285 : fialc[169]: mace_client_init: Client already connected
LC/0/0/CPU0:May 18 07:02:17.286 : fialc[169]: mace_client_init: Client already connected
LC/0/0/CPU0:May 18 07:02:17.287 : fialc[169]: mace_client_init: Client already connected
LC/0/0/CPU0:May 18 07:02:19.911 : fialc[169]: mace_client_init: Client already connected
LC/0/0/CPU0:May 18 07:02:19.911 : fialc[169]: mace_client_init: Client already connected
LC/0/0/CPU0:May 18 07:02:19.912 : fialc[169]: mace_client_init: Client already connected
LC/0/0/CPU0:May 18 07:02:19.912 : fialc[169]: mace_client_init: Client already connected
LC/0/0/CPU0:May 18 07:02:21.403 : mace_fpd_agent[249]: DEBUG: FPD ltrace (fpd-agent/mace_fpd_agent) Initialization successful for mace_fpd_agent
LC/0/0/CPU0:May 18 07:02:22.052 : mace_fpd_agent[249]: %PLATFORM-UPGRADE_FPD-4-DOWN_REV : cpld1 instance 0 is down-rev (V0.19), upgrade to (V1.00). Use the "upgrade hw-module fpd" CLI in admin mode. 

*
* The idle timeout is soon to expire on this line
*
ios con0/RSP0/CPU0 is now available
Press RETURN to get started.
User Access Verification

Username: cisco
Password:
RP/0/RSP0/CPU0:ios(admin)#install add source tftp://64.1.1.1/ asr9k-services-p.pie-4.2.0 asr9k-k9sec-p.pie-4.2.0 asr9k-mpls-p.pie-4.2.0 sync
!---安装需要的PIE,这只是安装到disk0中,如果应用,需要激活
Fri May 18 08:03:30.369 UTC
Install operation 5 '(admin) install add source /tftp://64.1.1.1/
asr9k-services-p.pie-4.2.0 asr9k-k9sec-p.pie-4.2.0 asr9k-mpls-p.pie-4.2.0
synchronous' started by user 'cisco' via CLI at 08:03:30 UTC Fri May 18 2012.
Info:     The following packages are now available to be activated:
Info:
Info:         disk0:asr9k-services-p-4.2.0
Info:         disk0:asr9k-k9sec-p-4.2.0
Info:         disk0:asr9k-mpls-p-4.2.0
Info:
Info:     The packages can be activated across the entire router.
Info:
Install operation 5 completed successfully at 08:04:31 UTC Fri May 18 2012.
RP/0/RSP0/CPU0:ios(admin)#install active disk0:asr9k-services-p-4.2.0 disk0:asr9k-k9sec-p-4.2.0 disk0:asr9k-mpls-p-4.2.0 sync
!---激活安装后的PIE文件
Fri May 18 08:06:17.801 UTC
Install operation 6 '(admin) install activate disk0:asr9k-services-p-4.2.0
disk0:asr9k-k9sec-p-4.2.0 disk0:asr9k-mpls-p-4.2.0 synchronous' started by user
'cisco' via CLI at 08:06:18 UTC Fri May 18 2012.
Info:     The following sequence of sub-operations has been determined to
Info:     minimize any impact:
Info:
Info:     Sub-operation 1:
Info:         Install Method: Parallel Process Restart
Info:         asr9k-mpls-p-4.2.0
Info:
Info:     Sub-operation 2:
Info:         Install Method: Parallel Process Restart
Info:         asr9k-k9sec-p-4.2.0
Info:
Info:     Sub-operation 3:
Info:         Install Method: Parallel Process Restart
Info:         asr9k-services-p-4.2.0
Info:
\ 28% complete: The operation can still be aborted (ctrl-c for options)RP/0/RSP0/CPU0:May 18 08:07:53.358 : insthelper[65]: ISSU: Starting sysdb bulk start session
\ 38% complete: The operation can still be aborted (ctrl-c for options)

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply third-party
authority to import, export, distribute or use encryption. Importers,
exporters, distributors and users are responsible for compliance with
U.S. and local country laws. By using this product you agree to comply
with applicable laws and regulations. If you are unable to comply with
U.S. and local laws, return this product immediately. 

A summary of U.S. laws governing Cisco cryptographic products may be
found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

| 38% complete: The operation can still be aborted (ctrl-c for options)RP/0/RSP0/CPU0:May 18 08:09:10.381 : ike[432]: %SECURITY-IMP-4-MSG_WARN : (ike_imp_chan_open) /dev/ipsec/imp Successful
RP/0/RSP0/CPU0:May 18 08:09:10.639 : ike[432]: %SECURITY-IKE-4-WARNING : You may want to configure a hostname
RP/0/RSP0/CPU0:May 18 08:09:10.650 : ike[432]: %SECURITY-IKE-4-WARNING : You may want to configure a domain-name
- 61% complete: The operation can still be aborted (ctrl-c for options)RP/0/RSP0/CPU0:May 18 08:09:15.073 : insthelper[65]: ISSU: Starting sysdb bulk start session
\ 95% complete: The operation can still be aborted (ctrl-c for options)RP/0/RSP0/CPU0:May 18 08:10:42.301 : insthelper[65]: ISSU: Starting sysdb bulk start session
Info:     The changes made to software configurations will not be persistent
Info:     across system reloads. Use the command '(admin) install commit' to
Info:     make changes persistent.
Info:     Please verify that the system is consistent following the software
Info:     change using the following commands:
Info:         show system verify
Info:         install verify packages
- 100% complete: The operation can still be aborted (ctrl-c for options)RP/0/RSP0/CPU0:May 18 08:10:55.096 : instdir[241]: %INSTALL-INSTMGR-4-ACTIVE_SOFTWARE_COMMITTED_INFO : The currently active software is not committed. If the system reboots then the committed software will be used. Use 'install commit' to commit the active software.
Install operation 6 completed successfully at 08:10:55 UTC Fri May 18 2012.
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#sh ins ac sum
Fri May 18 08:12:18.892 UTC
Default Profile:
  SDRs:
    Owner
  Active Packages:
    disk0:asr9k-services-p-4.2.0
    disk0:asr9k-mini-p-4.2.0
    disk0:asr9k-k9sec-p-4.2.0
    disk0:asr9k-mpls-p-4.2.0
RP/0/RSP0/CPU0:ios(admin)#install commit
本文出自 Frank's Blog

版权声明:


本文链接:Upgrade XR for ASR9k/CRS/GSR by TURBOBOOT
版权声明:本文为原创文章,仅代表个人观点,版权归 Frank Zhao 所有,转载时请注明本文出处及文章链接
你可以留言,或者trackback 从你的网站

5 Responses to “Upgrade XR for ASR9k/CRS/GSR by TURBOBOOT”

  1. LIGYAN说道:

    An related ENGLISH article for reference:

    https://supportforums.cisco.com/docs/DOC-29251

  2. frank说道:

    里面已经有这个link了,看蓝色背景的信息~

  3. LIGYAN说道:

    How to format like this:
    /disk1: FAT16 FAT32 2.0G Mounted 0720934 Formatted Restar
    /disk1a: FAT16 FAT32 2.0G Mounted 0720934

    Normally we see like that:
    /disk1: FAT16 FAT32 3.4G Mounted 0930002 Formatted Restarted
    /disk1a: FAT16 FAT16 0.5G Mounted 0930002 Restarted

    Which size should we use ? 2G/2G or 3.4G/0.5G ?

  4. frank说道:

    1. only format way:

    “format disk1: partition filesystem fat32 location 0/RP1/CPU0”

    Currently, you should format standby RP, then resync and boot normal for standby RP, then switchover, then use same way to format disk0:

    2. if need delete partition, e.g: you want to delete 2G, you can reference follow link:
    http://www.qnx.com/developers/docs/6.4.1/neutrino/utilities/m/mount.html

    If need, I will summary this on new article.

  5. ligyan说道:

    “sync”:
    – type ‘sync’ after setting the rommon variable:
    – the ‘sync’ is effectively ‘save’.

    otherwise the new image will be saved in mem than in disk0, with following error:

    rommonA instance 0 is down-rev (V2.03), upgrade to (V2.10). Please consult TAC or Firmware Upgrade documentation before proceeding to upgrade rommonA.

    %INSTALL-TURBOBOOT-4-ROMMON_VARIABLE_NOT_SET : TURBOBOOT rommon variable not set; system is membooting. Set TURBOBOOT rommon variable to ‘on’ to diskboot the system.!! Memboot is unsupported. Behavior could be undefined !!

留言哦

blonde teen swallows load.xxx videos